Anet A8+ resurrection - Ramps1.6 on Mega2560 (1 reply)
All, I am repairing/upgrading my antique Anet A8Plus. I burned out the extruder motor driver on the original Anet board by pulling jammed TPU filament out of the hot end. That generated enough voltage...
View ArticleRamps 1.4 > 1.6 "No data" (no replies)
Hello On a printer I just changed the ramps 1.4 > 1.6 under marlin 1.8. Everything works fine except the card which is well inserted but message "no data" (tested with 2 displays). SD card ok and...
View ArticleRamps 1.4 fuses (2 replies)
Dear all, I want power a Ranps 1.4 board with 24V. I read that I have to remove the D1 diode, check all capacitor ratings and replace the fuses. In my case, I only want to drive the stepper motor's...
View ArticleWrong Axis is moving:( (6 replies)
Hi there, I have set up a custom built printer using Ramps 1.4 and Marlin. My problem is that when i want to move z the x axis moves everything else is completely working and ok. Thanks for any help....
View ArticleFaulty thermistor readings on RAMPS 1.4 (no replies)
Hi, I've got an MKS Gen-2Z v1.1 control board based on RAMPS 1.4 and recently after starting the printer the heated bed readings are fluctuating. If I try to heat the bed the LED is lighting up and...
View ArticleMy RAMPS1.4 doesn't work when controlled by Raspberry PI 5 via Python3 (no...
Hello, When I use my Windows device to control ramps1.4 (mounted on mega Arduino) via Python3, by g code like this: ... import serial import time myPort = serial.Serial('COM7', 250000, parity='N')...
View ArticlePreheat test damaged the board - ramps 1.4 (1 reply)
Hello everyone, I'm building a custom 3d printer using ramps 1.4 board. Thanks to reprap community, I've completed to run motors and endstoppers very quickly. I have connected the mk3 heatbed to D8...
View ArticleProblem with output D10 (no replies)
Hello. I built a homemade printer using ramps 1.4 and I have a problem with the extruder. When I energize the ramps, the extruder starts to heat up and continues indefinitely (it only stops heating...
View ArticleTriple z motor controller with Ramps 1.4 (2 replies)
Hi, I'm not sure if this has been considered previously and already solved (or maybe its not a good Idea), I am keen on a Voron esk printer, but I'm not keen on the price, I was thinking I can get a...
View ArticleRamps 1.4 in bq witbox - hotend heizt nach Einschalten sofort auf (1 reply)
Hallo! Ich habe eine bq witbox und bin eigentlich sehr zufrieden damit! Nun musste ich das Ritzel beim Extruder tauschen, wobei es dann an einer wohl im Betrieb durchgescheuerten Stelle an einem Kabel...
View ArticleRamps 1.4 bed temp errors (no replies)
I hate to bring this up, given past articles, but here goes: Upgraded to Marlin 2.1.2.1 (may or may not be significant), also installed magnetic surface with magnetic rubber backing on glass plate,...
View ArticleProblem using Ramps 1.4 with LabView (5 replies)
Hey everyone I have already asked this question on the official NI forum and haven't gotten a reply yet, so I'm posting here to see if someone can help me with this. I want to control Ramps 1.4 and...
View ArticleHow do I wire external 5v for servo? (no replies)
I have a ramps1.4/mega2560 and I have come to the conclusion that my bltouch(generic made by geeetech) is drawing more amps than the mega board can put out because when the probe deploys it makes the...
View Articlehi friends Pin 8 not turn on for heated bed (1 reply)
my board is KFB 3.0 all is active(endstops - probe z - bed leveling) but heated bed on pin 8 not power This shows the error: start Printer is now online. echo:Marlin 2.0.5 echo: Last Updated:...
View ArticleClik here to view.
MKS BASE 1.4 and FYSTEC RGB LCD (2 replies)
Hi everyone, as i'm not an expert in 3D printer electronics, i went here to find a solution : I want to use a RGB Mini12864 Panel with an MKS BASE 1.4 from an old Tevo Tarnantulla ( Old Gen.) The...
View ArticleClik here to view.
Some Questions on RepRapDiscount Full Graphic Smart Controller (2 replies)
reprap-ramps-14-compatible-128x64-full-graphic-smart-24116-21-B.jpg What does the potasiometer on the bottom-left is doing? Which pin does the Stop button connects when Mega is connected with RAMPS...
View ArticleMega's AMS 1117 5V Getting Hot with RAMPS 1.6 + 128*64 LCD (6 replies)
I have placed RAMPS 1.6 on my Arduino Mega Clone. When I feed RAMPS 1.6 with 12V 2A, the AMS 1117 component on Mega is getting hot. I might have attached fans to D9 and D10 in the wrong direction and...
View ArticleRamps 1.6 and 3 pin Fan for Cooling (1 reply)
Dear RepRap Forum members, I am using RAMPS 1.6 with 4 TM2208 drivers. I want to cool these drivers with a 3 pin (red, black, white) fan. How should I connect the fan and run it? Best regards. bkarpuz
View Articlestep size, bed size for RAMPS + A4988 (1 reply)
Hello, I am trying to build a CNC machine with a small XYZ stage. The motors are 24V x 0.6A, 1.8 degree/step. The stage uses M6 leadscrew. The motor drivers are A4988. I am using all 3 jumpers for...
View ArticleRamps 1.6 and AccelStepper Library (1 reply)
Dear RepRap forum members, I would like to run my Nema 17 motors connected to Arduino Mega 2560+Ramps 1.6+Drv8825 with the AccelStepper library. I have the mechanical connections set properly as I can...
View Article![Cloonee, Yandel & ATLAC – Movimiento – Single [iTunes Plus M4A]](http://i.imgur.com/Q8tO40p.jpeg)
