Ramps LED an D8 (no replies)
Hallöle! Mein Drucker hat jetzt frisch LED's bekommen (Gerade 8 Strips -> 2 an jedem Profil an den Drucker verbaut). Diese sind jetzt noch an das Netzteil angeschlossen, das möchte ich aber ändern....
View ArticleLooking for a reliable RAMPS kit and PSU+relay (2 replies)
Hey, I am looking for a good reliable RAMPS kit with: -Arduino Mega -RAMPS -Stepper Drivers -LCD Screen Plus, I am looking for a good 12v 500w PSU and 12v to 12v dc SSR (I am looking for stuff on Ebay...
View ArticleArduino - driver interface components (1 reply)
Hello all, I was wondering whether the arduino mega (2560) pins and the DRV8825 pins have components between them. I suspect not, but i am uncertain. I was hoping somebody would know. I have looked at...
View ArticleRAMBo Fan 0 connection (no replies)
I am using a Rambo (v1.2 I think) and having some difficulty with my Fan 0 (bed fan). Command M106 S* does seem to control the output to the fan, but the Fan only seems to work if it is between about...
View ArticleTouch Screens and GUI's? (2 replies)
Hi Guys and Girls, Just wondering if there are any TFT monitors that have built in Processors that can be used with a RAMPS setup and if so has anyone designed a GUI for such a device? Thanks Ryan.
View Article12V from RAMPS to Arduino (3 replies)
Hi there, I know Arduino gets 12V through RAMPS and in Arduino it goes through 5V regulator and powers on the Arduino. I know about frying the 5V regulator on Arduino. I have fried mine and replaced...
View ArticleVmot accidentally shorted to GND, why does this affect the arduino? [RAMPS...
Short and sweet, I made the stupid mistake of trying to replace the X-axis stepper driver while the unit was on, using metal needle-nose pliers. I saw a spark when Vmot was shorted to GND by the...
View ArticleSome problems about RMAP1.4 connect to wifi shield (no replies)
Hello everyone, i have some troubles with transmitting string(g code) between RMAP1.4 and wifi shield board. And i set RMAP1.4 for serial port 3 . (Attachment is my wiring) But the lcd didn't show...
View Article1.5 years I decided to ask, why my motors only work in one direction. (2...
I have tried everything I can think of. I still can't seem to get my 3d printer going. I also have a cnc router with an Arduino cnc shield I have used to test all the motors, drivers, and my...
View Articlea4988 to 8825 (1 reply)
ramps has 3 jumpers per stepper driver works with a 4988 but what to do if using 8825 that has 4 jumper settings ?
View Articleramps and usb (1 reply)
if the ramps 12 volt is the source of power to the arduino via the 5 volt regulator what happens if a usb from a computer is plugged in as well supplying 5 volts or would a special usb cord be needed...
View ArticleWhatelse i can do with ramps 1.4? (2 replies)
So i got my old prusa mendel i2 with ramps 1.4 sitting here, and i wonder What else i can do with it? I got a better printer and its gettin dust I already have a dremmel turning intro a router would...
View ArticleNot sure what settings control drift per layer (no replies)
So yesterday I made the yellow part on the left, the part is skewed so I adjusted the machine, and adjusted the z Axis I had it set to 500, it should have been 2500 since I had to manually adjust the...
View ArticleMy bed stopped heating. (4 replies)
I have a printer of my own design that uses a Rambo controller. It has worked flawlessly for well over a year...until this morning. I tried to do a print and discovered that the bed was not heating....
View ArticleRE-ARM's now on kickstarter (no replies)
Hey Guys Have a look at this board. [www.kickstarter.com] I have been testing it for quite a while and with big success. There's ofcourse a learning curve changing from marlin to smoothieware but when...
View ArticleRAMPS 1.4 without D1 (3 replies)
Hello, I'm the (almost) happy owner of a prusa i3 with RAMPS 1.4, that has never wanted to work. I was having some weird voltage issues where arduinos would get fired if I connected them to my PC, so...
View ArticleDid i shorten my ramps 1.4? (no replies)
Hello I just wantet to set the pot on the a4988 stepper drivers. Connected usb for power. One pin on the screw one pin on gnd. Three of the five Steppers gave me a voltage, two didnt. Connected the...
View Articlee3d v6 pt100 MAXTEMP triggered (1 reply)
Hello everyone, i got a Problem with my pt100 from e3d. I followed the Doc here: [wiki.e3d-online.com] But the only thing that happen is that the Max Temparture was triggered and the printer turns...
View ArticleRamps 1.4 stepper driver help (no replies)
Hey Can somebody help me with wiring a "BIG EASY DRIVER" to the ramps 1.4 ? :) this driver...
View Article