7805 for 12v to 5v (probe) (1 reply)
First, let me just say I have no formal training with electronics and learn basically everything I know about it online, so please forgive my ignorance in advance. Trying to add an inductive sensor to...
View ArticleMosfet Installation (1 reply)
Hi there , anyone got the diagram for the Arduino board 1.4 ramps to install a Mosfet on it ?
View ArticleMakerbase MKS Slot2 V1.0 + RepRapDiscount Full Graphics LCD + RAMPS 1.4 (2...
I want to add an external SD card adapter on my RepRapDiscount Full Graphics LCD. My 3D printer is based on (Arduino Mega + RAMPS v1.4 + RepRapDiscount Full Graphics LCD). I buy an SD Card Adapter...
View ArticleCoronavirus Mechanical ventilator (no replies)
Hello Everyone, As most people are aware, there is a world wide shortage of Mechanical ventilators. There are a lot of hobbyists working on this idea to produce quickly to market. [e-vent.mit.edu] My...
View ArticleTMC2130 standalone stopped working (no replies)
Hi to all, So for the last few weeks, my ramps 1.4 setup was running TMC2130 Bigtreetech V3 in standalone mode on my 3d printer for X and Y-axis. The printer was off for a couple of days and suddenly...
View ArticleDebugging RAMPS for heated bed problem (1 reply)
Hi, Earlier this week I started using my printer but the heated bed refused to work. I googled for hints what to try but couldn't figure out the cause of the problem. Except things to measure from...
View ArticleTMC2209 fried - It was inserted correctly (no replies)
Hey, I installed two tmc2208 for Z and extruder and two tmc2209s for X and Y axis yesterday in UART mode. I made sure the drivers (made by Bigtreetech) were inserted correctly, checked the DIR and EN...
View ArticleIR Probe (dc42), Ramps 1.4, Digital Mode Issue (no replies)
Hello, everyone, I have the following problem when integrating an IR Probe (https://www.duet3d.com/IRProbe) on my Ramps 1.4 with Marlin 2.0.x: No matter what I do, the red LED on the IR Probe lights...
View ArticleBed Thermistor - readings are off, im at a loss. (2 replies)
Struggling to get the bed heater temperature to read correctly on the Ramps 1.4.. I bought brand new 100k NTC 3950 thermistors on Amazon (since I used old spare ones and couldn't figure out what they...
View ArticleRAMPS 1.4 AND MARLIN (no replies)
Does anyone have experience changing the Marlin firmware to display heated enclosure temperature on the status LCD? I believe I am close but at the moment both temperature displays are reading from...
View ArticleRepRapDiscount Full Graphics Smart Controller Menu Scrolling Issue (1 reply)
Hello All, I decided to build my own 3D printer (Marlin FW, Arduino Mega, Ramps 1.4) and recently purchased a RepRapDiscount Full Graphics Smart Controller to use with it. I have connected it up and...
View ArticleProblem with RepRapDiscount Smart Controller - Marlin (3 replies)
Hi, I have self-made 3D printer assembled and I started to configurating Marlin. I have issue with RepRapDiscount Smart Controller, more precisley with launching it. I've configurated Marlin by...
View ArticleDumb question- what is all displayed on the Ramps LCD? (no replies)
I've tried looking on the repetier site but couldn't find much. See the picture posted, what is the E: 0.20 shown on the screen?
View ArticleThermistor sensor value without Firmware (1 reply)
I'd like to support the value of temperature from Thermistor with Arduino Mega and Ramps 1.4 but without using any Firmware like Merlin. Right now I use the follow code and all feature works well but...
View ArticleDIAMOND x5 on RAMPS with stepper extender x3 problem PIN D1 (DIR) on AUX-1 (6...
I came to operate the 5 extruders for the DIAMOND x5 (FULL COLOR) and everything seemed ok (apart from the cobwebs, I am fighting with the percolation of the nozzle and the retraction) but in the end...
View ArticleRepRap Full Graphics Display (no replies)
I purchased a graphics display from 3DMakerWorld (thru Amazon) because they were a US manufacturer and their boards should be better than the cheaper Chinese clones. The printer it was purchased for...
View ArticleRamps 1.4 not powering extruder or motors (3 replies)
Hello, I have a reprap prusa i3 rework. Connected to my ramps 1.4 shield is an Arduino mega 2560. I run it with marlin and pronterface. The problem is when I use pronterface my ramps have stopped...
View Articlebed is not centered and is offset and Steps/mm are all over the place (3...
Hey all, it's my first time using ramps 1.4 or even marlin for that matter. I just upgraded from an ANet A8 after my board crapped out and after the nightmare that was setup without this forum as a...
View ArticleRAMPS 1.4 and MEGA 2560 Printer Setup Help (3 replies)
Howdy I've claimed this reprap printer from a mate, it was a project for guys doing an apprenticeship and it fell by the way side. I couldn't let it be thrown away or just left to gather dust. I'm...
View ArticleVoltage drop cause print job to stop (2 replies)
Hello, I build a 3d printer. It works fine in normal use but when I turn on Air Conditioner (AC) in my house. There is voltage drop seen in house. Which as a result cause voltage drop on 3d printer...
View Article