Hello, a few days ago I had assembled a 3d printer using Ramp 1.4 and Arduino Mega 2560. After installing Marlin firmware, I had opened pronterface and tried to move X,Y or Z axis but it make noise and doesn't move. I had not install heated bed yet but hotend is working fine. When I click X,Y or Z homing it gives an [ERROR] Error printer halted. kill() called!. All the endstop is opened but not triggered. Copy of the firmware is also attached. I hope if anyone can help me out. Thank you
↧
Error: printer halted. kill (Make noise) (no replies)
↧
X Motor Malfunction, Please Help (1 reply)
Fair warning: this is my first 3D printer. I don’t know a ton about the stuff involved, I have done some looking on the interwebs to attempt to resolve the problem on my own, but to no avail.
I’ve recently assembled my OneUp printer, which I’ve had partially assembled in my attic for years. Finally decided to finish. Finished that and then got on to configuring the Repetier software and testing it. Everything seems fine except that now my X motor doesn’t work. That is, the motor is fine (because it works if I connect to the Y or Z plug on my RAMPS board). When attempting to use manual control to move it, it will sometimes sort of... jitter. Don’t know how else to say it. It like goes a little bit and goes right back immediately. I mean, a very little bit. Like a few degrees of the motor. The motor does continue to receive power fine, which I can tell merely because I can’t manually move the X car without cutting the power to the motor. It works fine if I connect it to the Y or Z motor plugs on my board. I don’t know what else to do at this point to diagnose the issue. I thought that maybe it could be a firmware issue, but I have no idea where to get different firmware to use or if that would actually fix it. I’m not sure what to do to determine if it’s a board issue or something, I do have all the appropriate tools to diagnose the issue and make repairs if I need to, I’m just not sure where to start at this point.
I can give more information if needed. Any help would be greatly appreciated.
For anyone unfamiliar, the OneUp was originally designed and sold by Q3D, who is now gone and all but erased from the internet. The manuals can be found here though: [archive.org]
I’ve recently assembled my OneUp printer, which I’ve had partially assembled in my attic for years. Finally decided to finish. Finished that and then got on to configuring the Repetier software and testing it. Everything seems fine except that now my X motor doesn’t work. That is, the motor is fine (because it works if I connect to the Y or Z plug on my RAMPS board). When attempting to use manual control to move it, it will sometimes sort of... jitter. Don’t know how else to say it. It like goes a little bit and goes right back immediately. I mean, a very little bit. Like a few degrees of the motor. The motor does continue to receive power fine, which I can tell merely because I can’t manually move the X car without cutting the power to the motor. It works fine if I connect it to the Y or Z motor plugs on my board. I don’t know what else to do at this point to diagnose the issue. I thought that maybe it could be a firmware issue, but I have no idea where to get different firmware to use or if that would actually fix it. I’m not sure what to do to determine if it’s a board issue or something, I do have all the appropriate tools to diagnose the issue and make repairs if I need to, I’m just not sure where to start at this point.
I can give more information if needed. Any help would be greatly appreciated.
For anyone unfamiliar, the OneUp was originally designed and sold by Q3D, who is now gone and all but erased from the internet. The manuals can be found here though: [archive.org]
↧
↧
Strange problem with Z axis (5 replies)
Finished replacing the mainboard of my Malyan M150 with a RAMPS 1.4 after the former burnt out, followed the guides etc. Everything seems to be working ok, with all axis' homing properly like they did originally by hitting the min stops and backing off. However, when attempting to print, the Z axis motors move the extruder downwards for each layer instead of upwards. Really scratching my head on what is causing this, can anyone help please?
↧
Heatbed Automatically Heating up without setting temperature and reach more than 100 degree. (2 replies)
Hello. I had made prusa i3 and facing some problem. As I turn on my 3d printer the heatbed automatically start heating up without setting up the Max temperature. For reference i had upload the picture of my lcd(heatbed.png) after few minutes the 3d printer was on . I have 12V, MK3 Aluminum Heatbed and connected through heatbed power module. I had also upload Marlin Firmware. I hope if anyone can help me out. Thank you
Link for Mosfet used. [www.amazon.com]
Link for Mosfet used. [www.amazon.com]
↧
Ramps 1.4 heated bed not heating up (4 replies)
I have a ramps 1.4 board it was working normally i left it for 2 months and started it back hotend heat up normally, but heated bed is not heating up (board heated bed led not lighting up) there is no output from the board.
What should i check first?
What should i check first?
↧
↧
Sdramps (1 reply)
Is there anyway to print directly from a Sdramps? I prefer to print untethered from a PC. I can see and select a file on the card when I'm in Repetier host but if I disconnect the PC it kills the print. I was hoping I could turn on the printer and have it load the file and start the print. I would only have one file on the SD card. I usually use a smart controller but have been having EMI problems since relocating all of my electronics to the base of the printer.
↧
FlashAir (no replies)
Hello, I recently discovered this wonderful little SD card.
Discovered them from Chris Riley through this vid: WiFi SD Card
I can save my gcode files straight to the SD card through Wifi, BUT the Marlin firmware (1.1.9) wont read the card.
(The card powers up, I can find and save files to the card so, "its working")
Marlin detects that its inserted, but when I go to load the code from from the menu, it says "No SD card"
I made the changes listed here: Marlin Firmware Patch
But that didn't help.
Any suggestions?
Discovered them from Chris Riley through this vid: WiFi SD Card
I can save my gcode files straight to the SD card through Wifi, BUT the Marlin firmware (1.1.9) wont read the card.
(The card powers up, I can find and save files to the card so, "its working")
Marlin detects that its inserted, but when I go to load the code from from the menu, it says "No SD card"
I made the changes listed here: Marlin Firmware Patch
But that didn't help.
Any suggestions?
↧
full graphic smart lcd controller NO SD CARD DETECTED FOR LONG CABLE (no replies)
hi guys my FULL GRAPHIC SMART LCD CONTROLLER is broken so i change it by buying an new FULL GRAPHIC SMART LCD CONTROLLER...
the problem is : my new FULL GRAPHIC SMART LCD CONTROLLER cant read my SD card i get always NO SD CARD but if i put the small cables i can read my SD card !!!!!!!! so with my new FULL GRAPHIC SMART LCD i cant learn my SD card if i use a long cable why please ?
look at the size of cables in pictures:
[ibb.co]
[ibb.co]
[ibb.co]
![50027877-371558273423822-1784248071819886592-n.jpg]( "50027877-371558273423822-1784248071819886592-n.jpg")
![50103836-367817587330250-2155985733330927616-n.jpg]( "50103836-367817587330250-2155985733330927616-n.jpg")
![50509183-628807370912456-5574509066467672064-n.jpg]( "50509183-628807370912456-5574509066467672064-n.jpg")
what should i do :/ i need a long cable :/
my long cable i made it with this cable:
[www.aliexpress.com]
why my old broken FULL GRAPHIC SMART LCD CONTROLLER can learn SD CARD with a long cable, and my new FULL GRAPHIC SMART LCD CONTROLLER cant learn it ?
is there any problem in ramps ? jumper ? marlin need more configuration ???
help please
the problem is : my new FULL GRAPHIC SMART LCD CONTROLLER cant read my SD card i get always NO SD CARD but if i put the small cables i can read my SD card !!!!!!!! so with my new FULL GRAPHIC SMART LCD i cant learn my SD card if i use a long cable why please ?
look at the size of cables in pictures:
[ibb.co]
[ibb.co]
[ibb.co]
what should i do :/ i need a long cable :/
my long cable i made it with this cable:
[www.aliexpress.com]
why my old broken FULL GRAPHIC SMART LCD CONTROLLER can learn SD CARD with a long cable, and my new FULL GRAPHIC SMART LCD CONTROLLER cant learn it ?
is there any problem in ramps ? jumper ? marlin need more configuration ???
help please
↧
full graphic smart lcd controller EXTERN SD CARD ADAPTER (no replies)
Ok Buys
i need this adapter with an extern SD CARD ADAPTER
![Adaptateur-LCD-pour-ramps-1-4.jpg]( "Adaptateur-LCD-pour-ramps-1-4.jpg")
is there any adapter can let me use an externe SD CARD adapter and let me keep using my full graphic smart lcd controller
Thank you
i need this adapter with an extern SD CARD ADAPTER
is there any adapter can let me use an externe SD CARD adapter and let me keep using my full graphic smart lcd controller
Thank you
↧
↧
Mks Gen 1.4 (4 replies)
Question. The Image is labeled Mks Gen 1.4 Wiring Diagram New Ramps 14
Does anyone know anything about this controller.
Information of where to get one. Schematics to build one ect...
[attachment 109761 mks-gen-1-4-wiring-diagram-new-ramps-1-4-stepper-motor-wiring-wiring-solutions-of-mks-gen-1-4-wiring-diagram.jpg]
Does anyone know anything about this controller.
Information of where to get one. Schematics to build one ect...
[attachment 109761 mks-gen-1-4-wiring-diagram-new-ramps-1-4-stepper-motor-wiring-wiring-solutions-of-mks-gen-1-4-wiring-diagram.jpg]
↧
RAMPS 24v (1 reply)
Hi,
I am seeking advice for a 24v setup. I want to use the 24v because of the 300x300 printbed I plan.
An external MOFSET for the heated bed would be absolutely fine if not even preffered.
I plan an i3 style printer. Not sure yet if one or two z steppers.
I want to be able to run Marlin but also wnat to try Klipper.
I have an Arduino Mega 2560 lying arround. I checked some ebay kits, but they all come with an Arduino.
It doesn't need to be a RAMPS board. Just thought it would save some budget as I can use the MEGA.
Do I actually need to have other special components if going for 24v? Like the hotend or stepper drivers?
Thanks a lot in advance for your support.
I am seeking advice for a 24v setup. I want to use the 24v because of the 300x300 printbed I plan.
An external MOFSET for the heated bed would be absolutely fine if not even preffered.
I plan an i3 style printer. Not sure yet if one or two z steppers.
I want to be able to run Marlin but also wnat to try Klipper.
I have an Arduino Mega 2560 lying arround. I checked some ebay kits, but they all come with an Arduino.
It doesn't need to be a RAMPS board. Just thought it would save some budget as I can use the MEGA.
Do I actually need to have other special components if going for 24v? Like the hotend or stepper drivers?
Thanks a lot in advance for your support.
↧
Problems with EEB configuration after adding Servo (1 reply)
When I added a servo to my EEB configuration, the servo goes crazy when the layer fans come on.
Modded A8 with RAMPS 1.4 and Marlin, with the following fan/servo pins configured:
FAN_PIN 5
E0_AUTO_FAN_PIN 4
E1_AUTO_FAN_PIN 4
SERVO0_PIN 11
I made a dual extruder setup, changed Marlin to EEB and used a fan extender board in the servo header to run the hotend and layer fans. I added a servo for the Z-probe (had to shift the extender board by 2 pins so it uses D4,D5 but that worked fine) and the servo deploys and retracts perfectly.
Problem comes when I hit layer 4 and the fan comes on... the servo goes mental and after a few seconds the computer loses comms with the printer. It then appears on another ttyACMx port.
I tried the following without success:
1. Moving the servo from D11 to D6 and changing the pin assignment in pins_RAMPS.h
2. Removing the Vcc/5v jumper and powering the servo connector directly from 5v (vie the remaining GND/5v pins in the servo header block)
3. Replacing the USB cable
Now I'm wondering whether Marling uses a different PWM mode for servos and for fans, and if so whether there's a workaround.
Also somewhat confused as to why the USB port would be affect, and why it then directly reappears as a new com port.
Any suggestions greatly appreciated.
Thanks,
Phil
Modded A8 with RAMPS 1.4 and Marlin, with the following fan/servo pins configured:
FAN_PIN 5
E0_AUTO_FAN_PIN 4
E1_AUTO_FAN_PIN 4
SERVO0_PIN 11
I made a dual extruder setup, changed Marlin to EEB and used a fan extender board in the servo header to run the hotend and layer fans. I added a servo for the Z-probe (had to shift the extender board by 2 pins so it uses D4,D5 but that worked fine) and the servo deploys and retracts perfectly.
Problem comes when I hit layer 4 and the fan comes on... the servo goes mental and after a few seconds the computer loses comms with the printer. It then appears on another ttyACMx port.
I tried the following without success:
1. Moving the servo from D11 to D6 and changing the pin assignment in pins_RAMPS.h
2. Removing the Vcc/5v jumper and powering the servo connector directly from 5v (vie the remaining GND/5v pins in the servo header block)
3. Replacing the USB cable
Now I'm wondering whether Marling uses a different PWM mode for servos and for fans, and if so whether there's a workaround.
Also somewhat confused as to why the USB port would be affect, and why it then directly reappears as a new com port.
Any suggestions greatly appreciated.
Thanks,
Phil
↧
MKS_GEN_L board (1 reply)
I have Ender 3 and wanted to install a better motherboard with bootloader and more memory .I bought MB and it came with Artillery 3D firmware flashed on the board . I installed the drivers 2208 and set Vref. When I tried to flash compiled version of Malin 1.1.9 board did not recognize any of my COM ports. The Tools COM ports in Marlin is grayed out. So far I belong to several different facebook forums I could not get no satisfactory answers.Maybe someone here can give me good advice .
↧
↧
trouble with extruder stepper motor (1 reply)
my setup:
mega2560 board (x2)
Ramps 1.4 (x2)
A4988 stepper drivers (2 full sets + spares)
Geared extruder with large gear removed for troubleshooting.
Z stepper motors disconnected from threaded rod for trouble shooting.
I use an LED stepper substitute driver tester from [reprap.org]
I have 4 built on pref board.
I also use a RepRap Easy Driver test board [reprap.org]
all stepper motors have been tested for functionally and all driver boards have been adjusted and tested using above equipment and a spare stepper motor.
I use Repetier on a PC in Manual control mode to control actions.
The problem:
All axis steppers function well.
My extruder runs fine in the feed direction but makes grinding noises and does not move in the retract direction.
Trouble shooting:
I have tested with 2 different mega2560 & Ramps hardware setups and both Marlin 1.1.9 and 1.1.4 with same results.
I have plugged in a different stepper motor, swapped one z axis stepper and extruder stepper,
problem remains with extruder driver.
Changed out A4988 and problem still there.
Just to avoid the "standard query" the system was fully powered down and disconnected from PC before any changes where made.
Logic says the problem must be in the Arduino or its software, the Ramps board, the Stepper drivers, wiring or the stepper motors.
I am at a loss as to why this is happening as I have changed everything.
I am wondering if there is some setting for the extruder that I have wrong.
As the configuration.h edits have been ported from 1.1.4 to 1.1.9 and 1.1.4 had worked previously I don't think that should be the case
any Ideas???
mega2560 board (x2)
Ramps 1.4 (x2)
A4988 stepper drivers (2 full sets + spares)
Geared extruder with large gear removed for troubleshooting.
Z stepper motors disconnected from threaded rod for trouble shooting.
I use an LED stepper substitute driver tester from [reprap.org]
I have 4 built on pref board.
I also use a RepRap Easy Driver test board [reprap.org]
all stepper motors have been tested for functionally and all driver boards have been adjusted and tested using above equipment and a spare stepper motor.
I use Repetier on a PC in Manual control mode to control actions.
The problem:
All axis steppers function well.
My extruder runs fine in the feed direction but makes grinding noises and does not move in the retract direction.
Trouble shooting:
I have tested with 2 different mega2560 & Ramps hardware setups and both Marlin 1.1.9 and 1.1.4 with same results.
I have plugged in a different stepper motor, swapped one z axis stepper and extruder stepper,
problem remains with extruder driver.
Changed out A4988 and problem still there.
Just to avoid the "standard query" the system was fully powered down and disconnected from PC before any changes where made.
Logic says the problem must be in the Arduino or its software, the Ramps board, the Stepper drivers, wiring or the stepper motors.
I am at a loss as to why this is happening as I have changed everything.
I am wondering if there is some setting for the extruder that I have wrong.
As the configuration.h edits have been ported from 1.1.4 to 1.1.9 and 1.1.4 had worked previously I don't think that should be the case
any Ideas???
↧
Ramps mit PT1000 (1 reply)
Hallo Leute,
ich brauche mal etwas Hilfe.
Ich habe einen Anet A6 kommplett umgebaut auf ALU-Mechanik. Teile Gedreht und gefräst. Dann die Elektronik auf RAMPS 1.4 umgebaut mit Marlin 1.1.9. Läuft soweit alles.
Nun wollte ich das Druckbett noch vergrößern. Habe nun eines gefunden 220x270 mm. Dort ist ein Termistor verbaut dessen Typ ich halt nicht kenne und daher ist die Temperatur des Bed ca. 15 Grad zu niedrig entgegen der Anzeige.
Da ich bei den Termistoren gesehen habe, dass man auch PT100 oder PT1000 einsetzen kann und ich diese seit langer Zeit kenne, möchte ich PT1000 einsetzen. Am besten mit 1KOhm Pullup. Ich denke, hierdurch kann man am besten den Temperaturbereich nutzen.
Hat jemand damit Erfahrung und was wäre evtl. auf dem Ramps umzubauen? Kann ich den PT1000 direkt an den vorherigen Thermistoreingang anschließen? Reicht es wenn ich dann in der Config den Typ 1010 angebe?
Viele Grüße
Franz
ich brauche mal etwas Hilfe.
Ich habe einen Anet A6 kommplett umgebaut auf ALU-Mechanik. Teile Gedreht und gefräst. Dann die Elektronik auf RAMPS 1.4 umgebaut mit Marlin 1.1.9. Läuft soweit alles.
Nun wollte ich das Druckbett noch vergrößern. Habe nun eines gefunden 220x270 mm. Dort ist ein Termistor verbaut dessen Typ ich halt nicht kenne und daher ist die Temperatur des Bed ca. 15 Grad zu niedrig entgegen der Anzeige.
Da ich bei den Termistoren gesehen habe, dass man auch PT100 oder PT1000 einsetzen kann und ich diese seit langer Zeit kenne, möchte ich PT1000 einsetzen. Am besten mit 1KOhm Pullup. Ich denke, hierdurch kann man am besten den Temperaturbereich nutzen.
Hat jemand damit Erfahrung und was wäre evtl. auf dem Ramps umzubauen? Kann ich den PT1000 direkt an den vorherigen Thermistoreingang anschließen? Reicht es wenn ich dann in der Config den Typ 1010 angebe?
Viele Grüße
Franz
↧
Thermistor giving wrong value (2 replies)
I bought a ntc thermistor and soldered it, but the thermistor shows the wrong value, I wonder where the error, can i change the marlin to t0 pin t2
Value is always 52 °C
Value is always 52 °C
↧
Anyone using a PICA ramps board? (no replies)
Is anyone using a PICA board? Its a RAMPS derivative.
[www.tindie.com]
[github.com]
There was a bit of a user base on reprapwilson forum on discourse, but sadly its vanished and no followup info there.
I have one and am having an intermittent issue and hoping to network with some other PICA owners.
thanks
sinneD
[www.tindie.com]
[github.com]
There was a bit of a user base on reprapwilson forum on discourse, but sadly its vanished and no followup info there.
I have one and am having an intermittent issue and hoping to network with some other PICA owners.
thanks
sinneD
↧
↧
NeoPixel/WS2812B on Trigorilla (RAMPS 1.4) (1 reply)
Hi guys,
I would like to add an RGB strip to my printer that can be controlled via Marlin. There's already a lot to find, but mostly for regular RGB strips, which use 3 pins on the board and have to be equipped with transistors.
Now since Marlin has support for NeoPixel/WS2812B LEDs, that would simplify the whole thing. Power the strip externally with 5V and add only one wire for control on board, as far as I understand it. Has anyone had any experience with the Trigorilla board? And if yes, which pin would be suitable?
Best regards,
David
I would like to add an RGB strip to my printer that can be controlled via Marlin. There's already a lot to find, but mostly for regular RGB strips, which use 3 pins on the board and have to be equipped with transistors.
Now since Marlin has support for NeoPixel/WS2812B LEDs, that would simplify the whole thing. Power the strip externally with 5V and add only one wire for control on board, as far as I understand it. Has anyone had any experience with the Trigorilla board? And if yes, which pin would be suitable?
Best regards,
David
↧
[TMC2130][PSU on/off] Request for a bit of hacking (1 reply)
Hello
I am trying to make these drivers to work, but I have my PSU by default, I have just arise an Issue in github\MARLIN so that the M122 command does not work if the psu is off (I have the protectors on so no problem with EM issues)
I have 2 psu on my printer, one small that turns on with the printer and feeds the RAMPS and arduino ,and other 12V PSU which turns on when MARLIN sends M80 GCODE.
The question is :
HAs someone come up with an idea to deal with these drivers without the 12v psu on...a jumper, a diode, more cabling?
I hope you understand what I am requesting!!
Let me know if you need more information.
Thank you all.
I am trying to make these drivers to work, but I have my PSU by default, I have just arise an Issue in github\MARLIN so that the M122 command does not work if the psu is off (I have the protectors on so no problem with EM issues)
I have 2 psu on my printer, one small that turns on with the printer and feeds the RAMPS and arduino ,and other 12V PSU which turns on when MARLIN sends M80 GCODE.
The question is :
HAs someone come up with an idea to deal with these drivers without the 12v psu on...a jumper, a diode, more cabling?
I hope you understand what I am requesting!!
Let me know if you need more information.
Thank you all.
↧
silicone heater (no replies)
Hi,
I am looking to upgrade my heated bed to a 220v 200w 200*200mm silicone heater, would the EinyRambo support this mod. Would i able to put in a 20a fuse for both the motors and heaters rather than the standard 15a and 5a fuse.
Or would I need an ssr/ mosfet
Please help ,
I am looking to upgrade my heated bed to a 220v 200w 200*200mm silicone heater, would the EinyRambo support this mod. Would i able to put in a 20a fuse for both the motors and heaters rather than the standard 15a and 5a fuse.
Or would I need an ssr/ mosfet
Please help ,
↧