Error: printer halted. kill (Make noise) (no replies)
Hello, a few days ago I had assembled a 3d printer using Ramp 1.4 and Arduino Mega 2560. After installing Marlin firmware, I had opened pronterface and tried to move X,Y or Z axis but it make noise...
View ArticleX Motor Malfunction, Please Help (1 reply)
Fair warning: this is my first 3D printer. I don’t know a ton about the stuff involved, I have done some looking on the interwebs to attempt to resolve the problem on my own, but to no avail. I’ve...
View ArticleStrange problem with Z axis (5 replies)
Finished replacing the mainboard of my Malyan M150 with a RAMPS 1.4 after the former burnt out, followed the guides etc. Everything seems to be working ok, with all axis' homing properly like they did...
View ArticleHeatbed Automatically Heating up without setting temperature and reach more...
Hello. I had made prusa i3 and facing some problem. As I turn on my 3d printer the heatbed automatically start heating up without setting up the Max temperature. For reference i had upload the picture...
View ArticleRamps 1.4 heated bed not heating up (4 replies)
I have a ramps 1.4 board it was working normally i left it for 2 months and started it back hotend heat up normally, but heated bed is not heating up (board heated bed led not lighting up) there is no...
View ArticleSdramps (1 reply)
Is there anyway to print directly from a Sdramps? I prefer to print untethered from a PC. I can see and select a file on the card when I'm in Repetier host but if I disconnect the PC it kills the...
View ArticleFlashAir (no replies)
Hello, I recently discovered this wonderful little SD card. Discovered them from Chris Riley through this vid: WiFi SD Card I can save my gcode files straight to the SD card through Wifi, BUT the...
View ArticleClik here to view.
full graphic smart lcd controller NO SD CARD DETECTED FOR LONG CABLE (no...
hi guys my FULL GRAPHIC SMART LCD CONTROLLER is broken so i change it by buying an new FULL GRAPHIC SMART LCD CONTROLLER... the problem is : my new FULL GRAPHIC SMART LCD CONTROLLER cant read my SD...
View ArticleClik here to view.
full graphic smart lcd controller EXTERN SD CARD ADAPTER (no replies)
Ok Buys i need this adapter with an extern SD CARD ADAPTER Adaptateur-LCD-pour-ramps-1-4.jpg is there any adapter can let me use an externe SD CARD adapter and let me keep using my full graphic smart...
View ArticleMks Gen 1.4 (4 replies)
Question. The Image is labeled Mks Gen 1.4 Wiring Diagram New Ramps 14 Does anyone know anything about this controller. Information of where to get one. Schematics to build one ect... [attachment...
View ArticleRAMPS 24v (1 reply)
Hi, I am seeking advice for a 24v setup. I want to use the 24v because of the 300x300 printbed I plan. An external MOFSET for the heated bed would be absolutely fine if not even preffered. I plan an...
View ArticleProblems with EEB configuration after adding Servo (1 reply)
When I added a servo to my EEB configuration, the servo goes crazy when the layer fans come on. Modded A8 with RAMPS 1.4 and Marlin, with the following fan/servo pins configured: FAN_PIN 5...
View ArticleMKS_GEN_L board (1 reply)
I have Ender 3 and wanted to install a better motherboard with bootloader and more memory .I bought MB and it came with Artillery 3D firmware flashed on the board . I installed the drivers 2208 and...
View Articletrouble with extruder stepper motor (1 reply)
my setup: mega2560 board (x2) Ramps 1.4 (x2) A4988 stepper drivers (2 full sets + spares) Geared extruder with large gear removed for troubleshooting. Z stepper motors disconnected from threaded rod...
View ArticleRamps mit PT1000 (1 reply)
Hallo Leute, ich brauche mal etwas Hilfe. Ich habe einen Anet A6 kommplett umgebaut auf ALU-Mechanik. Teile Gedreht und gefräst. Dann die Elektronik auf RAMPS 1.4 umgebaut mit Marlin 1.1.9. Läuft...
View ArticleThermistor giving wrong value (2 replies)
I bought a ntc thermistor and soldered it, but the thermistor shows the wrong value, I wonder where the error, can i change the marlin to t0 pin t2 Value is always 52 °C
View ArticleAnyone using a PICA ramps board? (no replies)
Is anyone using a PICA board? Its a RAMPS derivative. [www.tindie.com] [github.com] There was a bit of a user base on reprapwilson forum on discourse, but sadly its vanished and no followup info...
View ArticleNeoPixel/WS2812B on Trigorilla (RAMPS 1.4) (1 reply)
Hi guys, I would like to add an RGB strip to my printer that can be controlled via Marlin. There's already a lot to find, but mostly for regular RGB strips, which use 3 pins on the board and have to...
View Article[TMC2130][PSU on/off] Request for a bit of hacking (1 reply)
Hello I am trying to make these drivers to work, but I have my PSU by default, I have just arise an Issue in github\MARLIN so that the M122 command does not work if the psu is off (I have the...
View Articlesilicone heater (no replies)
Hi, I am looking to upgrade my heated bed to a 220v 200w 200*200mm silicone heater, would the EinyRambo support this mod. Would i able to put in a 20a fuse for both the motors and heaters rather than...
View Article