RAMPS 1.6 Jumper problem (no replies)
I am Trying to add BLtouch on my Ramps 1.6 .. when i am adding jumper on (5V and VCC ) Board is going turns off. I dont get it whats is goin on. (Ramps Powerd with 12V 360W power supply) Any advice?
View ArticleReprap Full Graphic Smart Controller starts beeping and flashing backlight (1...
Hi all, suddenly the RepRap Full Graphic Smart Controller Board on my Fabricator Mini 1.5 started to flash the backlight and beep in roughly a one second rhythm. A few minutes earlier it was still...
View ArticleLed blue display 12864A (3 replies)
Hello, o buy a LCD raystar screen blue 12864a . Can you Help me in One Isseu? The screen works but the color blue is off. I check the pins 19 (+5 v) and 20 (gnd) and it os ok. Why the blue color don't...
View ArticleRamps 1.4 power source wiring problems (5 replies)
Hey Guys, I might've burned my ramps 1.4 board (maybe?). The thing is I don't know what I did wrong, so I wanna ask you for your best-educated guesses as I'm pretty new to this stuff. So here's what...
View ArticleStepper motor driver А4988 on Ramps 1.4 smoked out. Why? (2 replies)
Hey Guys, So I'm trying to get a Nema 17 stepper motor running on Ramps 1.4. I'm using a driver А4988 for that and a 12v power supply. When I connected the power supply only, everything seemed to...
View ArticleTimeout when uploading to CR-10 S5 (2 replies)
Hey guys, I'm upgrading my CR-10S5 to Marlin 2.0. I got it all configured and it uploaded no problem. Then I went to use the UBL and realized I didn't uncomment the line for the BLTouch. So I went it...
View ArticleRAMPS 1.4 voltage question (no replies)
I recently got a RAMPS 1.4 board, and I've converted it for use with 24 volt. I've followed the multitude of videos and articles on how to do this, which all of them are practically doing the same...
View ArticleI burned Arduino on ramps 1.6 - Dunno why... (24 replies)
I am doing my 3D printer project. i wanted to set on my 3d printer bl-touch. i short vcc 5v with jumper on mega 1.6. The board turned off immediately and my arduino just burned in 3 sec. Can someone...
View ArticleArduino mega 2560 + ramps 1.4 (1 reply)
Guys I need to control 2 stepper motors to rotate continuously I have the 1.4 ramps and the arduino mega 2560 but the motors don't work I don't know how to program the arduino correctly. OBS: the...
View ArticleRAMPS driver signal strength - Four motor z-axis (2 replies)
I've built a machine which uses 4 motors in the z-axis (picture attached). All the units have been tested individually using the A4988, which is slightly under powered. I've ordered 9 of the TB6600...
View ArticleNew Heated Bed Isn't Even Showing Up? Ramps 1.4 Build (1 reply)
I am running Marlin 2 on a Ramps 1.4 and Arduino Mega 2560 kit. I enabled #define pidbedtemp (sorry if spelled wrong), and I set the thermistor 1 (as thermsitor 0 is the hotend) to the 100K Ohm type....
View Articleheat bed stalls print (no replies)
Hello, Lately, I have been seeing issues relating to my print bed heating. Printing pauses repeatedly because of the heat bed (I think): Recv: T:239.94 /240.00 B:64.93 /65.00 @:86 B@:88 W:? Recv:...
View ArticleSMART-RAMPS 2.0 - Six Stepper version with Pico (no replies)
Hi All. My main board has been a SMART-RAMPS board, and it has been awsome! Love the openness of it and flexibility. I'd modified mine for 24V and it worked with Mega2460 and Duo boards...
View ArticleHeated bed problems on custom CoreXY (no replies)
Hi!! I'm gonna write the best I can my problem. I built a Hypercube CoreXY, it's not my first printer but is my first Arduino + Ramps 1.4. The thing is all on the printer works fine except the heated...
View ArticleRamps 1.4 and Marlin - D8 and D9 Linked (3 replies)
Hello, Have a bit of an issue with my ramps setup after updating firmware. If I turn my cooling fan on (via D9) or turn my heated bed on (D8) the other pin will also turn on. Its almost as if they are...
View ArticleHeating with D8-D9-D10 (no replies)
Dear community, I am using Arduino Mega and RAMPS 1.4 for creating a custom control (without using MARLIN) for the extruder. I am using a Dyze Design Pulsar which is using 3 heaters. I have connected...
View ArticleM106 P0 controls D8, but D9 is always on (3 replies)
I have a Mega2560 + RAMPS1.4 controlling an old 3d printer that I want to convert to a laser engraver, and I followed this page from marlin on how to set this up for lasers. I've been trying to test...
View ArticleClik here to view.
Probably fried my stepper driver. What did I do wrong? (2 replies)
Hello everyone, So I’m new to this, and I’ve recently bought some stuff for a private pick and place machine. In order to learn, I first wanted to try and control a single stepper motor and obviously...
View ArticleMOSFET PCB not working? (2 replies)
Hi, I hope someone has come across this problem before. I bought some of these MOSFET boards and I can't seem to get them to work. I have my power hooked up correctly, the heater on the output. I've...
View ArticlePower surge error with connection rumba board (1 reply)
Hi, I am replacing a rumba board over GT2560 for geetech i3 pro B but as soon as I attache one of the min wires (x or y or z) I face power surge error. Does anyone know what is wrong with it? Thanks
View Article